advanced search

The Basics of Electrical Systems

Jan 1, 2002 12:00 PM, By Mike Holt, Mike Holt Enterprises, Inc.

Do you understand neutrals and fault current paths?

Neutral connections, fault current paths, and grounding considerations can be confusing, but if you understand the basic principles of electricity, you can clear up the confusion every time.

Consider current flow. Electrons leaving a power supply are always trying to return to it — they are not trying to go into the earth. Alternating current applied to a transformer primary induces a voltage in the secondary. This induced voltage causes electrons to leave one end of the transformer secondary, travel over the conductors, through the load, and return over the remaining conductors to the other end of the transformer secondary. Comparing what utilities do on their side of the meter to what we do on ours illustrates key concepts.

Multipoint grounded neutral (utility).

Utilities use a multipoint grounded neutral system, in which the neutral conductor is electrically connected to earth approximately every quarter mile of distribution lines and at distribution transformers and service equipment (see the Figure).

Neutral current path.

Utilities ground the neutral conductor to the earth at multiple locations (parallel path for neutral current) to reduce the impedance of the return neutral current path. This reduces neutral voltage drop and line-to-ground voltages; it also helps clear line-to-neutral faults.

Fault current path.

Utilities connect metal parts of equipment to earth and to the neutral conductor (parallel path for fault current) to provide a low-impedance path for clearing line-to-case faults. If the neutral conductor opens, the earth should still have sufficient low impedance to clear a high-voltage line-to-case fault. For example, consider a typical 7.2kV line protected by a 100A fuse. With an impedance of 25 ohms, the earth should have no problem carrying sufficient fault current to open a 100A fuse (I5E4Z, I57,200V425 ohms, I5288A).

Single-point grounded neutral (our side of the meter).

Premises wiring not over 600V uses a single-point grounded neutral system, in which the neutral conductor connects to the earth and metal parts of the electrical system only at service equipment and at separately derived systems.

Neutral current path.

Neutral current should flow only on the grounded (neutral) conductor, not the effective fault current path or the earth.

Fault current path.

Metal parts of premise wiring should be bonded to an effective fault current path that provides a low-impedance path necessary to clear line-to-case faults. Fault current should flow only on the effective fault-current path, not the grounded conductor (neutral) or earth.

For systems operating at 600V or less, the earth will not carry sufficient fault current to clear a line-to-case fault. For example, a 120V fault to the earth (assuming a 25-ohm resistance) will draw only 4.8A (I = E/Z, I = 120/425 ohms, I = 4.8A), which won't open a 15A protection device.

---

Acceptable Use Policy blog comments powered by Disqus

Browse Back Issues Select an Issue November 2011 October 2011 September 2011 August 2011 July 2011 June 2011 May 2011 April 2011 March 2011 February 2011 January 2011 December 2010 November 2010 October 2010 September 2010 August 2010 July 2010 June 2010 May 2010 April 2010 March 2010 February 2010 January 2010 December 2009 November 2009 October 2009 September 2009 August 2009 July 2009 June 2009 May 2009 April 2009 March 2009 February 2009 January 1, 2009 December 2008 November 2008 October 1, 2008 September 2008 August 2008 July 2008 June 1, 2008 May 2008 April 2008 March 2008 February 2008 January 2008 December 2007 November 2007 October 2007 September 2007 August 2007 July 2007 June 2007 May 2007 April 2007 March 2007 February 2007 January 2007 December 2006 November 2006 October 2006 September 2006 August 2006 July 2006 June 1, 2006 May 1, 2006 April 2006 March 1, 2006 February 2006 January 2006 December 2005 November 2005 October 2005 September 2005 August 2005 July 2005 June 2005 May 2005 April 2005 March 2005 February 2005 January 2005 December 2004 November 2004 October 2004 September 2004 August 2004 July 2004 June 2004 May 2004 April 2004 March 2004 February 1, 2004 January 1, 2004 December 1, 2003 November 1, 2003 October 1, 2003 September 1, 2003 August 1, 2003 July 1, 2003 June 1, 2003 May 1, 2003 April 1, 2003 March 1, 2003 February 1, 2003 January 1, 2003 December 1, 2002 November 1, 2002 October 1, 2002 September 1, 2002 August 1, 2002 July 1, 2002 June 1, 2002 May 1, 2002 April 1, 2002 March 1, 2002 February 1, 2002 January 1, 2002 December 1, 2001 November 1, 2001 October 1, 2001 September 1, 2001 August 1, 2001 July 1, 2001 June 1, 2001 May 1, 2001 April 1, 2001 March 1, 2001 February 1, 2001 February 1, 1995 January 1, 2001 December 1, 2000 November 1, 2000 October 1, 2000 September 1, 2000 August 1, 2000 July 1, 2000 June 1, 2000 May 1, 2000 April 1, 2000 March 1, 2000 February 1, 2000 January 1, 2000 December 1, 1999 November 1, 1999 October 1, 1999 September 1, 1999 August 1, 1999 July 1, 1999 June 1, 1999 May 1, 1999 April 1, 1999 March 1, 1999 February 1, 1999 January 1, 1999 December 1, 1998 November 1, 1998 October 1, 1998 September 1, 1998 August 1, 1998 July 1, 1998 June 1, 1998 May 1, 1998 April 1, 1998 March 1, 1998 February 1, 1998 January 1, 1998 December 1, 1997 November 1, 1997 December 1, 1996 November 1, 1996 October 1, 1996 September 1, 1996 August 1, 1996 July 1, 1996 June 1, 1996 May 1, 1996 April 1, 1996 March 1, 1996 February 1, 1996 January 1, 1996 December 1, 1995 November 30, 1995 November 1, 1995 October 1, 1995 September 1, 1995 August 1, 1995 July 1, 1995 June 1, 1995 May 1, 1995 April 1, 1995 March 1, 1995

browse e-newsletters