Quizzes on the Code


Mobile Homes and Marinas

Choose the best answer:

  1. Aluminum, aluminum-alloy, and copper-clad aluminum conductors are permitted only for branch-circuit wiring in mobile and manufactured homes.
    (a) true
    (b) false

  2. All branch circuits that supply 15A and 20A, 125V outlets in bedrooms of _____ must be protected by AFCIs.
    (a) mobile homes
    (b) manufactured homes
    (c) a and b
    (d) none of these

  3. Service equipment can be mounted on or within a manufactured home.
    (a) true
    (b) false

  4. Private, noncommercial boat docking facilities _____ for use by the owner or residents of the associated single-family dwelling aren't covered by Art. 555.
    (a) constructed
    (b) occupied
    (c) a or b
    (d) none of these

  5. The electrical datum plane — land areas subject to tidal fluctuation — in a marina or boatyard is a horizontal plane _____ ft above the highest tide level under normal circumstances.
    (a) 1
    (b) 2
    (c) 3
    (d) 4

  6. A _____ is an enclosed assembly that can include receptacles, circuit breakers, fused switches, fuses, watt-hour meter(s), and monitoring means approved for marine use.
    (a) marine power receptacle
    (b) marine outlet
    (c) marine power outlet
    (d) any of these

  7. The disconnecting means for a boat must be readily accessible, not more than _____ from the receptacle it controls, and in the supply circuit ahead of the receptacle.
    (a) 12 in.
    (b) 24 in.
    (c) 30 in.
    (d) 36 in.

  8. Receptacles that provide shore power for boats must be _____.
    (a) rated not less than 30A
    (b) of the single-outlet type
    (c) of the locking and grounding-type, if rated 50A and less
    (d) all of these




Answers and Discussion

  1. (b), false. A new rule (550.15) in the 2002 NEC prohibits the use of aluminum wire in mobile and manufactured homes. This type of wire has traditionally been used to supply branch circuits for ranges, dryers, and electric furnaces.

  2. (c), a and b. A new rule (550.25) on arc-fault circuit interrupter (AFCI) protection for mobile and manufactured homes mirrors the AFCI requirements for dwelling units outlined in 210.12.

  3. (a), true. Service equipment can be installed in or on a manufactured home, provided the following conditions are met [550.32(B)].

    • The manufacturer must include in its written installation instructions indicating that the home must be secured in place by an anchoring system or installed on and secured to a permanent foundation.

    • The manufacturer must include in its written installation instructions one method of grounding the service equipment at the installation site. The instructions must clearly state that other methods of grounding are found in Art. 250.

    • A red warning label must be mounted on or adjacent to the service equipment, stating, “Warning: Do not provide electrical power until the grounding electrode(s) is installed and connected (see installation instructions).”

  4. (c), a or b. This rule was changed to clarify that the requirements of Art. 555 don't apply to boat docks at a single-family dwelling. For single-family dwellings, GFCI protection is required for all 15A and 20A, single-phase, 125V receptacles located outdoors or in boathouses [210.8(A)(3) and 210.8(A)(8)]. Although the Code doesn't define what a single-family dwelling unit is, it's safe to say a single-family dwelling unit and a single dwelling unit [Art. 100] are the same thing. Docking facilities at buildings containing more than one dwelling unit, such as duplexes, condominiums, and apartments, fall under the rules of Art. 555.

  5. (b), 2. A new definition in 555.2 ensures the proper placement of transformers [555.5], electrical connections [555.9], and shore power receptacles, in accordance with 555.19(A).

  6. (c), marine power outlet. A new definition in Art. 555.2 ensures the proper application of disconnecting means for shore power connections, in accordance with 555.17(B) and shore power receptacles, in accordance with 555.19(A).

  7. (c), 30 in. This new requirement (555.17) in the 2002 NEC was extracted from NFPA 303 — Fire Protection Standard for Marinas and Boatyards.

  8. (d), all of these. There is no specific requirement that the rating of a receptacle must be dependent on the length of the boat (555.19). Instead, the Code sets a minimum rating of 30A and leaves it up to the designer and/or owner to provide the receptacles they deem necessary based on projected usage of the slips.

Find More Code Quizzes »






Acceptable Use Policy
blog comments powered by Disqus

what's wrong here?

What's Wrong Here?

May 10, 2012 12:44 PM

What's Wrong Here?

Apr 19, 2012 10:09 AM

What's Wrong Here?

Apr 5, 2012 2:27 PM

View all What's Wrong Here?

product spotlight

EV charger tester

May 25, 2012 8:26 AM

EV charger tester

The Electrician is portable tester that verifies critical power and safety requirements of electric vehicle (EV) chargers...

View all 2012 Product Spotlights

Free Product Info

Our Product Information site is the ultimate online resource for products and services offered by Advertisers featured in our Magazine. This service is provided as a quick and easy way to request Product Information online. Get FREE product information now.

Recent Comments

More...


Social Media

More ways to stay informed...

follow us on twitter

Find us on Facebook

EC&M Whitepaper

Arc Mitigation –A Three-Step Approach

Did you know that an arc-flash incident hospitalizes 5-7 workers per day in North America, severely impacting processes and profitability with lost production? Download This Sponsored Whitepaper Today!

What's New in Residential Cabling?
Date: Wednesday, May 30, 2012
Time: 2:00pm ET


In this The Home Depot sponsored Low Voltage Webinar, Ron Kipper RCDD / NTS will discuss the need for compression style coaxial connectors and the migration of the entire CATV, Satellite and Audio / Video industry to them. Register Today!

Grounding Versus Bonding
Now Available On-Demand


In this 60-minute FREE webinar, Mike Holt of Mike Holt Enterprises, Inc. will explain the purpose of grounding and bonding as related to the most current requirements set forth in the 2011 NEC. Register to View On-Demand!

resources

product info icon

product info

tradeshow icon

tradeshow

research icon

research

industry links

industry links

rss icon

rss

Browse Back Issues

Browse Back Issues