ECM Buyers' Guide
  

Fire-Rated Ceilings: Don't Be Left Hanging

Fire-Rated Ceilings: Don't Be Left Hanging

Understanding how the NEC regards suspended ceiling designs and supports is critical for proper design and installation of electrical wiring and equipment.

As a designer and installer, you should know the fundamental differences between a suspended ceiling, which is an integral part of a fire-rated floor-ceiling or roof-ceiling assembly, and the far more common non fire-rated assemblies. It seems the National Electrical Code (NEC) revises Sec. 300-11 that deals with the use of suspended ceiling support wire and grid as a supporting means for electrical boxes, conduits, and cables in some manner in each of its publications since 1971.

Some floors have a thinner slab than one that would establish the required fire separation on its own. In this case, we consider the suspended ceiling an integral part of the overall fire rating.

If the ceiling manufacturer recognizes wiring in its ceiling support specifications, an exception in Sec. 300-11(a)(1) allows the system to support all electrical wiring and equipment. This means you don't have to put up additional support wires to accommodate electrical equipment. Unfortunately, it's rare for the designer to include this in the original plans.

Tested fire-rated assembly (Sec. 300-11(a)(1), Exception). Qualified testing laboratories evaluate many designs, using various ceiling panel materials. These tests involve constructing a test room and ceiling inside a giant furnace. As you can imagine, this is very expensive. The design specifies exactly how many support wires to use, how thick they must be, how and where to attach them, how fixtures support them, and how to construct and run air ducts.

These testing laboratories don't assume any additional weight loads on these support wires, nor do they (or could they) evaluate how such a ceiling might deform under fire conditions. In these cases, support the wiring securely and independently of the ceiling support wires.

The only exception allows for the remote possibility that someone might rerun a ceiling assembly test with electrical wiring attached to specified support wires. Since rated designs specify the support wire locations, both the electrical and building inspectors must recognize the difference between support wires used for the ceiling system and those used for electrical wires and equipment.

Fire-rated ceiling [Sec.300-11(a)(1)]. When installing electrical wiring in a non-tested ceiling, the 1999 NEC allows you a greater degree of latitude, permitting you to install additional support wires without requiring a cable tray system or trapeze arrangement of support wires.

Secure the independent ceiling support wires at both ends, making sure not to use the ceiling grid as a means of support for cables and raceways. You must identify such independent ceiling support wires by a distinguishable color, tagging, or other means acceptable to the AHJ.

Non fire-rated ceiling [Sec. 300-11(a)(2)]. In the case of non fire-rated applications, you'll need additional support wires for electrical cables and equipment; though you need not identify them. If you are using independent support wires, decide if you want these supports distinguishable by color, tagging, or other means from those that are part of the non fire-rated ceiling support system. You must also support independent support wires at both ends. The support wiring methods covered in this section of the Code are the same as the wiring methods discussed in the fire-rated ceiling design.


Want to use this article? Click here for options!





Acceptable Use Policy
blog comments powered by Disqus

what's wrong here?

What's Wrong Here?

Feb 2, 2012 7:54 PM

What's Wrong Here?

Jan 19, 2012 4:06 PM

What's Wrong Here?

Jan 5, 2012 11:53 AM

View all What's Wrong Here?

product spotlight

Labeling tool

Feb 10, 2012 7:58 AM

Labeling tool

The Rhino 4200 labeling tool features one-touch “hot keys” that quickly create and format wire/cable wraps, flags, fixed-length labels and more...

View all 2012 Product Spotlights

Free Product Info

Our Product Information site is the ultimate online resource for products and services offered by Advertisers featured in our Magazine. This service is provided as a quick and easy way to request Product Information online. Get FREE product information now.

Recent Comments

More...


Social Media

More ways to stay informed...

follow us on twitter

Find us on Facebook

EC&M TV

Arlington CP9000

Arlington's new 9" diameter ceiling cover plate is the neatest way to cover unused "high hat" cans. With no tools needed, installation couldn't be faster!...

Arlington Gangable Boxes

Designed for new or retrofit applications, these snap-together gangable plastic boxes eliminate the need to construct a multiple-gang steel box out of several individual ones...

Understanding NEC Requirements for Solar Photovoltaic Systems
During this session, Mike Holt will address possible conflicts or confusing NEC requirements, provide tips on proper electrical installation techniques, and discuss the dangers related to improper installations. View this On Demand Webinar!



resources

product info icon

product info

tradeshow icon

tradeshow

research icon

research

industry links

industry links

rss icon

rss

Browse Back Issues

Browse Back Issues