advanced search

Using demand data to analyze load additions.

May 1, 1995 12:00 PM, Stallcup, James G.

Can a new commercial or industrial load be added to existing service equipment without performing an extensive standard calculation?

For many years designers have struggled with doing standard load calculations in all types of existing commercial and industrial occupancies when confronted with requests to add loads to existing feeders and services. Effective with the 1981 NEC, however, there is a new approach that allows you to sidestep the more complicated standard calculation in cases where there are accurate electrical demand records going back over the last year.

Standard calculation

The standard calculation is a more detailed and comprehensive method and takes a great deal of time to complete. Not only do loads (which may number in the thousands) have to be determined and evaluated based upon their conditions of use, but they have to be classified as continuous or noncontinuous in operation. This is because the continuous loads need to be calculated at 125% for the purposes of sizing overcurrent protective devices. Finally, the Code allows you to apply demand factors to some or all of these loads. It helps to sort the loads into one of the following groups:

Load groupings:

* General lighting load.

* Receptacle load.

* Special appliance load.

* Largest noncoincident load.

* Motor load.

* Largest motor load.

Example:

Suppose you would like to add a 42A 3-phase load to an existing 208Y/120V service for a small office building with a restaurant on the first floor. The service is rated 350A and is wired with 400kcmil THWN service conductors. The existing load schedule consists of 80A of lighting load, 80A of receptacle load, and 150A of cooking load spread over ten appliances.

Calculating continuous load:

The lighting load will be continuous.

Step 1. Calculating load

Sec. 220-3(b); -10(b); Sec. 230-90(a) 80A x 125% = 100A

Solution: The calculated load is 100A.

Calculating noncontinuous load:

The receptacle load will usually be considered noncontinuous.

Step 1: Calculating load

Sec. 220-3(c)(6); -10(b); Sec. 230-90(a) 80A x 100% = 80A

Solution: The calculated load is 80A.

Calculating loads with demand factors:

The cooking equipment:

Step 1: Finding demand factor

Sec. 220-20; Table 220-20 10 units allows 65%

Step 2: Applying demand factors 150A x 65% = 97.5A

Solution: The demand load is 97.5A

Summation:

Step 1: Finding the existing total load Sec. 220-10(a)

100A + 80A + 97.5A = 277.5A Step 2: Add the new load 277.5A + 42A = 319.5A Step 3: Rate the service elements Art. 310, Table 310-16

400kcmil ampacity is 335A; overcurrent device given as 350A.

Solution: The new load can be added.

Optional calculation

For the purposes of allowing additional load to be connected to an existing service or feeder, you can also use actual maximum kVA demand figures to determine the existing load instead of using the standard calculation. You must, however, comply with all of the following conditions:

* The maximum demand data is available for a minimum period of one year.

* The existing demand at 125% plus the new load is not greater than the ampacity rating of the service conductors.

* The service-entrance conductors have suitable overcurrent protection.

Example:

If that small office/restaurant building has good demand records, you can use the optional calculation. If the highest demand recorded over the past year is 78.4kVA, could the new load be added?

Step 1: Calculating demand per NEC Sec. 220-35 78.4kVA x 125% = 98kVA

Step 2: Conversion to amperes

98,000VA/208V + [square root of 3] = 272A

Step 4: Calculating new total load

272A + 42A = 314A

Solution: The new load can be added. This approach, when possible, is much faster and easier.

Next issue

When can the service overcurrent protective device be sized higher than the ampacity of the service conductors?

James G. Stallcup is the owner of Grayboy & Associates in Fort Worth, Tex., a consulting firm specializing in the NEC.

Want to use this article? Click here for options!

© 2012 Penton Business Media, Inc.

---

Acceptable Use Policy blog comments powered by Disqus

Browse Back Issues Select an Issue EC&M Magazine | April 2012 March 2012 February 2012 January 2012 December 2011 November 2011 October 2011 September 2011 August 2011 July 2011 June 2011 May 2011 April 2011 March 2011 February 2011 January 2011 December 2010 November 2010 October 2010 September 2010 August 2010 July 2010 June 2010 May 2010 April 2010 March 2010 February 2010 January 2010 December 2009 November 2009 October 2009 September 2009 August 2009 July 2009 June 2009 May 2009 April 2009 March 2009 February 2009 January 1, 2009 December 2008 November 2008 October 1, 2008 September 2008 August 2008 July 2008 June 1, 2008 May 2008 April 2008 March 2008 February 2008 January 2008 December 2007 November 2007 October 2007 September 2007 August 2007 July 2007 June 2007 May 2007 April 2007 March 2007 February 2007 January 2007 December 2006 November 2006 October 2006 September 2006 August 2006 July 2006 June 1, 2006 May 1, 2006 April 2006 March 1, 2006 February 2006 January 2006 December 2005 November 2005 October 2005 September 2005 August 2005 July 2005 June 2005 May 2005 April 2005 March 2005 February 2005 January 2005 December 2004 November 2004 October 2004 September 2004 August 2004 July 2004 June 2004 May 2004 April 2004 March 2004 February 1, 2004 January 1, 2004 December 1, 2003 November 1, 2003 October 1, 2003 September 1, 2003 August 1, 2003 July 1, 2003 June 1, 2003 May 1, 2003 April 1, 2003 March 1, 2003 February 1, 2003 January 1, 2003 December 1, 2002 November 1, 2002 October 1, 2002 September 1, 2002 August 1, 2002 July 1, 2002 June 1, 2002 May 1, 2002 April 1, 2002 March 1, 2002 February 1, 2002 January 1, 2002 December 1, 2001 November 1, 2001 October 1, 2001 September 1, 2001 August 1, 2001 July 1, 2001 June 1, 2001 May 1, 2001 April 1, 2001 March 1, 2001 February 1, 2001 February 1, 1995 January 1, 2001 December 1, 2000 November 1, 2000 October 1, 2000 September 1, 2000 August 1, 2000 July 1, 2000 June 1, 2000 May 1, 2000 April 1, 2000 March 1, 2000 February 1, 2000 January 1, 2000 December 1, 1999 November 1, 1999 October 1, 1999 September 1, 1999 August 1, 1999 July 1, 1999 June 1, 1999 May 1, 1999 April 1, 1999 March 1, 1999 February 1, 1999 January 1, 1999 December 1, 1998 November 1, 1998 October 1, 1998 September 1, 1998 August 1, 1998 July 1, 1998 June 1, 1998 May 1, 1998 April 1, 1998 March 1, 1998 February 1, 1998 January 1, 1998 December 1, 1997 November 1, 1997 December 1, 1996 November 1, 1996 October 1, 1996 September 1, 1996 August 1, 1996 July 1, 1996 June 1, 1996 May 1, 1996 April 1, 1996 March 1, 1996 February 1, 1996 January 1, 1996 December 1, 1995 November 30, 1995 November 1, 1995 October 1, 1995 September 1, 1995 August 1, 1995 July 1, 1995 June 1, 1995 May 1, 1995 April 1, 1995 March 1, 1995

browse e-newsletters