advanced search

Tips For More Effective VFD Maintenance

Jul 1, 2001 12:00 PM, By Dave Polka, ABB Automation University

Find more articles on: Variable Frequency Drives

Do you know how to maintain variable frequency drives (VFDs)? It's easier than you might think, but it's something you shouldn't take for granted. By integrating some simple, logical steps into your preventive maintenance (PM) program, you can ensure your drives provide years of trouble-free service.

A VFD requires the same safety and equipment precautions applied to computers and power supplies because of its similarity to both: Keep it clean; keep it dry; and keep the connections tight.

Keep it clean. Most VFDs fall into a NEMA 1 (side vents for cooling airflow) or NEMA 12 (sealed, dust-tight enclosure) category. Side vents in NEMA 1 drives make VFDs susceptible to dust contamination, which can reduce airflow and diminish performance from heat sinks and circulating fans.

Dust on an electronic device can cause malfunction or even failure by absorbing moisture. Discharging compressed air into the VFD is a viable option in some environments, but typical plant air contains oil and water. Oil-free, dry air requires a specialized, dedicated, and expensive air supply — and you still run the risk of generating static charges. A nonstatic generating spray or a reverse-operated ESD vacuum will reduce static buildup. Common plastics are prime generators of static electricity. The material in ESD vacuum cases and fans is a special, nonstatic generating plastic.

Keep it dry. The photo above (not available online) shows what can happen to a control board periodically subjected to a moist environment. Initially, this VFD was wall-mounted in a clean, dry area of a mechanical room. However, problems arose when maintenance personnel installed a dehumidifier in an open space above the VFD. Unfortunately, the VFD was a NEMA 1 enclosure style (side vents and no seal around the cover). Water dripped from the dehumidifier into the drive. In six months, the VFD took on enough water to corrode the circuit board.

VFDs seldom offer condensation protection today. If you operate the VFD all day, every day, the normal radiant heat from the heat sink should prevent condensation. Unless the unit is in continuous operation, use a NEMA 12 enclosure and a thermostatically controlled space heater if you place it where condensation is likely.

Keep connections tight. This may seem obvious, but checking connections is a step many people miss or do incorrectly — and the requirement applies even in clean rooms. Heat cycles, mechanical vibration, and standard PM practices can lead to substandard connections. Also, retorquing screws and excessive tightening can ruin connections.

Bad connections eventually lead to arcing. Arcing at the VFD input could result in nuisance overvoltage faults, clearing of input fuses, or damage to protective components. Arcing at the VFD output could result in overcurrent faults, or even damage to the power components.

Loose control wiring connections can cause erratic operation. For example, a loose speed reference wire can cause the drive speed to fluctuate, resulting in scrap, machine damage, or injury.

Additional steps. The following maintenance requirements complement a good PM program.

1. When conducting a mechanical inspection, don't overlook internal VFD components. Check circulating fans for signs of bearing failure or foreign objects.

2. Inspect DC bus capacitors for bulging and leakage, which could be signs of component stress or electrical misuse.

3. Take voltage measurements while the VFD is in operation. Fluctuations in DC bus voltage measurements can indicate degradation of DC bus capacitors. One function of the capacitor bank is to act as a filter section (smoothing out any AC ripple voltage on the bus). Abnormal AC voltage on the DC bus indicates potential capacitor failure. Measurements of more than 4VAC may indicate a capacitor filtering problem or a possible problem with the diode bridge converter section (ahead of the bus). If you have such voltage levels, consult the manufacturer before taking further action.

   With the VFD in START and at zero speed, you should read output voltage of 40VAC phase-to-phase or less. Higher voltages could indicate transistor leakage. At zero speed, the power components should not be operating. Readings of 60VAC or more can indicate power component failure.

4. Store spare VFDs in a clean, dry environment. Place this unit in your PM system so you know to power it up every six months to keep the DC bus capacitors at their peak performance capability. Otherwise, their charging ability will diminish significantly.

5. Regularly monitor heat-sink temperatures. Most VFD manufacturers make this task easy by including a direct temperature readout on the keypad or display. Find this readout, and check it weekly or monthly.

   You wouldn't place your laptop outside, on the roof of a building, or in direct sunlight. A VFD needs the same consideration. Some manufacturers claim their VFDs offer 200,000 hr — almost 23 yr — of mean time between failures (MTBF). Such impressive performance is easy to obtain, if you follow these simple procedures.

Polka is a training manager with ABB Automation University, New Berlin, Wis.

Want to use this article? Click here for options!

© 2012 Penton Business Media, Inc.

---

Acceptable Use Policy blog comments powered by Disqus

Browse Back Issues Select an Issue EC&M Magazine | April 2012 March 2012 February 2012 January 2012 December 2011 November 2011 October 2011 September 2011 August 2011 July 2011 June 2011 May 2011 April 2011 March 2011 February 2011 January 2011 December 2010 November 2010 October 2010 September 2010 August 2010 July 2010 June 2010 May 2010 April 2010 March 2010 February 2010 January 2010 December 2009 November 2009 October 2009 September 2009 August 2009 July 2009 June 2009 May 2009 April 2009 March 2009 February 2009 January 1, 2009 December 2008 November 2008 October 1, 2008 September 2008 August 2008 July 2008 June 1, 2008 May 2008 April 2008 March 2008 February 2008 January 2008 December 2007 November 2007 October 2007 September 2007 August 2007 July 2007 June 2007 May 2007 April 2007 March 2007 February 2007 January 2007 December 2006 November 2006 October 2006 September 2006 August 2006 July 2006 June 1, 2006 May 1, 2006 April 2006 March 1, 2006 February 2006 January 2006 December 2005 November 2005 October 2005 September 2005 August 2005 July 2005 June 2005 May 2005 April 2005 March 2005 February 2005 January 2005 December 2004 November 2004 October 2004 September 2004 August 2004 July 2004 June 2004 May 2004 April 2004 March 2004 February 1, 2004 January 1, 2004 December 1, 2003 November 1, 2003 October 1, 2003 September 1, 2003 August 1, 2003 July 1, 2003 June 1, 2003 May 1, 2003 April 1, 2003 March 1, 2003 February 1, 2003 January 1, 2003 December 1, 2002 November 1, 2002 October 1, 2002 September 1, 2002 August 1, 2002 July 1, 2002 June 1, 2002 May 1, 2002 April 1, 2002 March 1, 2002 February 1, 2002 January 1, 2002 December 1, 2001 November 1, 2001 October 1, 2001 September 1, 2001 August 1, 2001 July 1, 2001 June 1, 2001 May 1, 2001 April 1, 2001 March 1, 2001 February 1, 2001 February 1, 1995 January 1, 2001 December 1, 2000 November 1, 2000 October 1, 2000 September 1, 2000 August 1, 2000 July 1, 2000 June 1, 2000 May 1, 2000 April 1, 2000 March 1, 2000 February 1, 2000 January 1, 2000 December 1, 1999 November 1, 1999 October 1, 1999 September 1, 1999 August 1, 1999 July 1, 1999 June 1, 1999 May 1, 1999 April 1, 1999 March 1, 1999 February 1, 1999 January 1, 1999 December 1, 1998 November 1, 1998 October 1, 1998 September 1, 1998 August 1, 1998 July 1, 1998 June 1, 1998 May 1, 1998 April 1, 1998 March 1, 1998 February 1, 1998 January 1, 1998 December 1, 1997 November 1, 1997 December 1, 1996 November 1, 1996 October 1, 1996 September 1, 1996 August 1, 1996 July 1, 1996 June 1, 1996 May 1, 1996 April 1, 1996 March 1, 1996 February 1, 1996 January 1, 1996 December 1, 1995 November 30, 1995 November 1, 1995 October 1, 1995 September 1, 1995 August 1, 1995 July 1, 1995 June 1, 1995 May 1, 1995 April 1, 1995 March 1, 1995

browse e-newsletters