advanced search

Access to Electrical Equipment

Oct 1, 2001 12:00 PM, By James Stallcup, Sr., NEC Consultant

When designing a workspace, you must maintain unobstructed pathways to and from electrical equipment per the NEC.

When designing and installing electrical equipment, you must provide for adequate illumination and easy access in and out of the workspace. To ensure a safe exit in case of a short-circuit or ground-fault, you must provide one way (and in some cases two) to enter or leave the workspace. If you don't, workers could get trapped at one end of the workspace with fire between them and the exit. The NEC has required a reliable entry and safe exit route for workers since 1978, and enforced the appropriate illumination rule since 1965.

So how do you design a workspace to meet the requirements of the NEC? A quality design and installation will address these requirements.

Access and entrance to working space [Secs. 110-26(a), (b), and (c), Exception 1]. For workers to take voltage measurements, check continuity of circuits, adjust or replace defective overcurrent protection devices, and tighten loose connections, electrical equipment must be accessible and located in an area with adequate working space. The space in front of electrical equipment must be free from stored materials that might block access to overcurrent protection devices — which must be accessible in case of emergencies — or the disconnecting means of equipment for routine maintenance.

Conditions allowing one entrance [Sec. 110-26(c)(1), Exception 1]. Where there is a continuous and unobstructed way of entrance and exit travel, the Code only requires one means of access to the working space. For example, if a support column blocks the route of travel, then you must provide another means of travel space.

Conditions requiring two entrances [Sec. 110-26(c)]. This requirement is crucial for people who work in the space discussed above. Remember, there must be at least one entrance large enough to give adequate working space to the electrical equipment inside. The NEC requires 6-ft or wider switchboards and control panels with a rating of 1,200A or more to have one entrance at each end that is at least 24 in. wide and 6½ ft tall. Thus, in some cases, at least two entrances must be available for safe and dependable entry and exit routes for workers.

Workspace doubled [Sec. 110-26(c) Exception 2]. The NEC requires one means of access and entrance to the working space where the workspace is doubled per Table 110-26(a), based on conditions 1, 2, or 3. With the workspace doubled in front of the equipment, a worker can move back out of the endangered workspace and exit along the length of the equipment. The deeper workspace in front of the equipment provides a safer route to exit without the expense of providing two entrances.

Illumination [Sec. 110-26(d)]. For the safety of the workers servicing the equipment, installations housing service equipment, switchboards, panelboards, and motor control centers must provide adequate lighting where live parts are accessible. Lighting fixtures may be incandescent, fluorescent, or any other type that provides the proper footcandles necessary to clearly illuminate the equipment and parts in service.

Lighting fixtures must have a headroom clearance of at least 6½ ft so people have sufficient room to stand in front of the equipment without their head or headgear contacting metal.

Appropriate clearances and proper workspace dimensions are mandatory. Therefore, it is imperative that the engineer determine the clearances necessary for providing a safe workspace in the design phase. This is especially true where the equipment is likely to require routine examination, adjustment, and maintenance — and where electricians will be exposed to energized parts. Electricians and inspectors must also ensure the equipment they install and inspect has an adequately sized workspace. It takes the combined efforts of engineers, electricians, and inspectors to comply with NEC and OSHA clearance and workspace rules.

Want to use this article? Click here for options!

© 2012 Penton Business Media, Inc.

---

Acceptable Use Policy blog comments powered by Disqus

Browse Back Issues Select an Issue November 2011 October 2011 September 2011 August 2011 July 2011 June 2011 May 2011 April 2011 March 2011 February 2011 January 2011 December 2010 November 2010 October 2010 September 2010 August 2010 July 2010 June 2010 May 2010 April 2010 March 2010 February 2010 January 2010 December 2009 November 2009 October 2009 September 2009 August 2009 July 2009 June 2009 May 2009 April 2009 March 2009 February 2009 January 1, 2009 December 2008 November 2008 October 1, 2008 September 2008 August 2008 July 2008 June 1, 2008 May 2008 April 2008 March 2008 February 2008 January 2008 December 2007 November 2007 October 2007 September 2007 August 2007 July 2007 June 2007 May 2007 April 2007 March 2007 February 2007 January 2007 December 2006 November 2006 October 2006 September 2006 August 2006 July 2006 June 1, 2006 May 1, 2006 April 2006 March 1, 2006 February 2006 January 2006 December 2005 November 2005 October 2005 September 2005 August 2005 July 2005 June 2005 May 2005 April 2005 March 2005 February 2005 January 2005 December 2004 November 2004 October 2004 September 2004 August 2004 July 2004 June 2004 May 2004 April 2004 March 2004 February 1, 2004 January 1, 2004 December 1, 2003 November 1, 2003 October 1, 2003 September 1, 2003 August 1, 2003 July 1, 2003 June 1, 2003 May 1, 2003 April 1, 2003 March 1, 2003 February 1, 2003 January 1, 2003 December 1, 2002 November 1, 2002 October 1, 2002 September 1, 2002 August 1, 2002 July 1, 2002 June 1, 2002 May 1, 2002 April 1, 2002 March 1, 2002 February 1, 2002 January 1, 2002 December 1, 2001 November 1, 2001 October 1, 2001 September 1, 2001 August 1, 2001 July 1, 2001 June 1, 2001 May 1, 2001 April 1, 2001 March 1, 2001 February 1, 2001 February 1, 1995 January 1, 2001 December 1, 2000 November 1, 2000 October 1, 2000 September 1, 2000 August 1, 2000 July 1, 2000 June 1, 2000 May 1, 2000 April 1, 2000 March 1, 2000 February 1, 2000 January 1, 2000 December 1, 1999 November 1, 1999 October 1, 1999 September 1, 1999 August 1, 1999 July 1, 1999 June 1, 1999 May 1, 1999 April 1, 1999 March 1, 1999 February 1, 1999 January 1, 1999 December 1, 1998 November 1, 1998 October 1, 1998 September 1, 1998 August 1, 1998 July 1, 1998 June 1, 1998 May 1, 1998 April 1, 1998 March 1, 1998 February 1, 1998 January 1, 1998 December 1, 1997 November 1, 1997 December 1, 1996 November 1, 1996 October 1, 1996 September 1, 1996 August 1, 1996 July 1, 1996 June 1, 1996 May 1, 1996 April 1, 1996 March 1, 1996 February 1, 1996 January 1, 1996 December 1, 1995 November 30, 1995 November 1, 1995 October 1, 1995 September 1, 1995 August 1, 1995 July 1, 1995 June 1, 1995 May 1, 1995 April 1, 1995 March 1, 1995

browse e-newsletters